Whole-home duct cleaning
Dryer vent cleaning
Camera inspection
Sanitizing & deodorizingWhole-system duct and dryer vent check with before-and-after photos - you see exactly what came out of your vents
That "$99 whole-house special" is a bait ad - the real number appears once they are in your hallway, or the "clean" is a shop-vac at the register. We photograph the inside of your ducts before and after instead.
Why Greensboro Homeowners Choose Lennox Air Duct Cleaning
We provide independent Lennox air duct cleaning service in Greensboro: full cleaning of the supply and return runs, the air handler cabinet and the evaporator coil, plus sealing and flex repairs on the Lennox equipment those ducts connect to. What makes our Lennox work different is that we treat the air handler, coil and ductwork as one system and inspect all three before we quote anything. We answer (833) 968-4577.
Duct Cleaning Greensboro is an independent Lennox service provider. We have worked on Lennox residential and light-commercial equipment across the Piedmont Triad, from older G-series gas furnaces and Merit-series air handlers to Dave Lennox Signature Collection systems. We are not authorized, affiliated with, or endorsed by Lennox, and we don’t pretend otherwise. That independence is useful to you: we diagnose what the equipment is actually doing and recommend only the work the ductwork and air handler genuinely need. No brand script, no upsell to a system you don’t need.
Why Trust Duct Cleaning Greensboro for Your Lennox Air Duct Cleaning?
Our technicians have up to 12 years of experience, and a good share of that has been spent inside Lennox cabinets – pulling cased A-coils, resetting gaskets, chasing down the flex takeoff that’s been leaking since the day it was installed. We know how these air handlers are assembled and what fails first on them in Greensboro’s climate.
We use professional-grade Rotobrush and Nikro equipment on every job, which matters with Lennox equipment because the coil face and blower wheel are where a shop vac can’t reach and a rushed blowout makes things worse. We clean it. We repair it. We protect it. Guardsman-backed finishing products go on treated surfaces to hold the results longer.
On parts, we use factory-style Lennox-compatible filters, flex, mastic and cabinet gaskets where fit matters, and quality aftermarket materials for the rest. We’re careful about warranty. Nothing we do in a cleaning or a duct repair touches the sealed refrigerant circuit or the heat exchanger, and we document what we found before we start, so your Lennox coverage stays intact. If something we find is a warranty matter, we tell you to take it to Lennox rather than quietly bill you for it.
Styles & brands we work with
- Whole-home duct cleaning
- Dryer vent cleaning
- Camera inspection
- Sanitizing & deodorizing
Common Lennox Air Duct Cleaning Problems We Fix in Greensboro
Lennox equipment is well built. The trouble almost always starts around it – in the coil face, the cabinet seams, and the flex runs the installer cut short on a hot afternoon. These are the five we see most in Greensboro homes.
- Matted, wet evaporator coil faces on Merit and Elite air handlers. A cased coil sits downstream of the filter, so everything the filter misses lands on it. In Greensboro’s humid summers that lint turns into a damp biofilm layer that narrows the coil face, raises static pressure and makes the blower run hot. Homeowners read it as weak airflow or a system that short-cycles.
- Crushed or separated flex takeoffs at the plenum. Lennox horizontal and upflow air handlers with factory-insulated flex have takeoffs that kink, crush or pull loose at the plenum when the run was never supported properly. The symptom is easy to spot: one or two rooms that whistle while the far end of the house gets almost nothing.
- Loosened cabinet and plenum seams. The mastic on Lennox furnace and air handler cabinets dries and cracks over time. Once a seam opens, the system pulls attic or crawlspace air straight into the return and lets filter-bypass dust ride past the coil.
- Return plenums pulling in crawlspace debris. A lot of Greensboro returns are built into the crawlspace with minimal sealing. Soil, fiberglass and pest debris get drawn in and load the filter and blower wheel faster than any homeowner expects from a filter change schedule.
- Blower wheels caked in dust from years of filter bypass. When air slips around the filter instead of through it, the wheel collects a hard, uneven crust. That imbalance shows up as noise, reduced airflow, and a motor working harder than it should.
Lennox Parts & Our Repair-vs-Replace Approach
We choose parts by fit, not by label. Filters, flex, mastic and cabinet gaskets that must seat correctly on a Lennox air handler get factory-style, Lennox-compatible parts, because a gasket that doesn’t seal leaves you right back where you started. For flex duct, sealing materials and general repair work, quality aftermarket components perform the same job without the OEM markup on consumables. We don’t claim to stock or order OEM parts, and we’re not a dealer. We’re an independent shop that repairs and services Lennox equipment with parts that fit it.
The repair-or-replace call comes down to the coil and the heat exchanger. If the air handler and coil are sound, cleaning and sealing is the honest recommendation – it costs less than a system and solves the airflow problem. If the coil is leaking refrigerant or the heat exchanger is failing, we say so plainly. Cleaning around a dead component just delays the bill. Call (833) 968-4577 and we’ll tell you which side of that line your Lennox system is on.
Our Lennox Service Process – Step by Step
- 1
Diagnosis. We start with a video inspection of the trunk, the branch runs and the air handler cabinet. On Lennox systems we pay particular attention to the coil face, the blower wheel, the flex takeoffs at the plenum and the cabinet seams, then measure static pressure so we know how much of the problem is duct restriction and how much is equipment.
- 2
Clean and repair. The coil and blower come out and get cleaned properly rather than brushed in place. Crushed flex is repaired or rerouted. Open plenum and cabinet seams get sealed with fresh mastic and correct gaskets. Where we find a component that’s failed, we quote the repair before we touch it.
- 3
Test. After reassembly we re-check static pressure and confirm airflow at the registers in the rooms that were weak before. Airflow at the far register is the number that actually matters to you.
- 4
Protect and document. Guardsman-backed finishing products go on treated surfaces to protect the results and extend how long the system stays clean. Before-and-after photos of your own ducts and coil go to you, plus a written note on anything we found that should go to Lennox as a warranty matter.
See the difference
Before
After
Before
After
Before
AfterLennox Products We Service & Install in Greensboro
We clean, seal and repair ductwork and air handlers on the Lennox equipment Greensboro homes actually run: Merit Series gas furnaces and air handlers, Elite Series split systems, G-series furnaces with cased A-coils, and Dave Lennox Signature Collection furnaces and heat pumps. The work we do on those systems is duct and cabinet work – air handler cleaning, evaporator coil cleaning and duct sealing – along with the flex and plenum repairs that usually turn up during a cleaning.
If your Lennox equipment needs refrigerant work, a heat exchanger replacement or a full system install, that’s a different trade and we’ll say so rather than take the job. What we can do is make sure the ducts, coil face and cabinet are doing their part first, because a lot of “failing” Lennox systems are really starving for airflow through a restricted duct system.
We Also Service These Brands
Lennox isn’t the only equipment we know. We also clean, seal and repair ductwork on Trane and Carrier systems, and the failure points are often similar – wet coils, loose plenum seams, crushed flex. That multi-brand experience keeps us honest about your Lennox system. We’re not pushing one manufacturer’s answer, and we’re not single-brand dependent. We read what the ductwork is doing and fix that.
FAQs – Lennox Air Duct Cleaning Service in Greensboro
No. We are an independent Lennox service provider, not authorized, affiliated with or endorsed by Lennox. We work on Lennox equipment because we’ve spent years inside it, not because the manufacturer sent us.
Yes. A generic cleaning sweeps the duct runs and stops there. On a Lennox air handler the coil face and blower wheel are where the real restriction builds up, and the cabinet and plenum seams are where air leaks in. Cleaning the ducts without pulling and cleaning the coil leaves the biggest problem in place.
Short-cycling after a cleaning usually points to one of two things: a coil that’s still restricted, or a takeoff that got disturbed while the ducts were being cleaned and is now leaking. A wet, matted coil face raises static pressure and makes the blower run hot. A separated flex takeoff at the plenum does something similar. Either one needs a video inspection and a static pressure reading to pin down, and we do both as part of the job.
Yes. The sealed refrigerant circuit stays closed and the coil gets cleaned in place on the cabinet side, with proper containment and rinse. We don’t open the refrigerant lines for a cleaning. If the coil itself is leaking refrigerant, that’s a different repair and we’ll tell you to take it to a licensed refrigerant tech rather than clean a coil that’s failing.
It is, and it’s one of the most common things we find in Greensboro. Dried mastic opens a seam, and the system starts pulling attic or crawlspace air straight into the return, letting dust ride past the coil. Resealing those seams with fresh mastic and correct gaskets is part of a proper Lennox cleaning job, not an add-on.
Where fit matters, yes – factory-style Lennox-compatible filters, flex, mastic and cabinet gaskets. For general repair materials like flex duct runs and sealing compounds, we use quality aftermarket parts because they perform the same job without the OEM markup. We don’t claim to stock OEM parts, and we’re not a dealer.
No. Duct cleaning, coil cleaning in place and cabinet sealing don’t touch the sealed refrigerant circuit or the heat exchanger, so your Lennox coverage stays intact. We document what we found before we start, and if we spot something that’s a warranty matter we tell you to take it to Lennox directly.
A single-system clean with coil and blower work usually runs a few hours, and it goes longer when we find crushed flex or need to repair plenum seams. We’ll give you a realistic window with the written estimate so you can plan the day.
Merit Series furnaces and air handlers, Elite Series split systems, G-series furnaces with cased A-coils, and Dave Lennox Signature Collection furnaces and heat pumps. The work is duct and cabinet work: air handler cleaning, evaporator coil cleaning, duct sealing and flex repair.
A typical whole-system cleaning with air handler and coil work generally runs in the mid-hundreds of dollars for a single Lennox system, and it goes up when we find flex or plenum repairs that need to be done at the same time. We set one flat price per system, agreed before work starts, with no per-vent pricing, so the written estimate is the final number. Call (833) 968-4577 for an exact quote – estimates are free.
Book Your Lennox Service in Greensboro, NC
If you’re in Greensboro and your Lennox system is short-cycling, whistling at one register, or pushing weak airflow to the far rooms, call (833) 968-4577. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. We’ll inspect the coil, cabinet and duct runs, quote one flat price per system before work starts, and send you before-and-after photos of your own ducts. Estimates are free.
Written by the team at Duct Cleaning Greensboro.